承接项目
新闻中心

玻璃钢假树是如何制作的?

玻璃钢材料是环氧树脂和玻璃纤维组合的复合材料,大批量生产成本相对来说比较低,单棵生产成本过高。玻璃钢材料的优点:
FRP is a composite material composed of epoxy resin and glass fiber. The cost of mass production is relatively low, and the cost of single production is too high. Advantages of FRP material:
1,耐腐蚀性,对大气.水.和一般浓度的酸碱盐等由很好的抵抗能力。
1. Corrosion resistance, good resistance to atmosphere, water, and general concentration of acid and alkali salt.
2,电性能好,用于制作绝缘体高频下能保护良好介电性,微博透过性良好。
2. Good electrical performance, good dielectric protection and microblog permeability when used to make insulator at high frequency.
3,热性能良好,广泛用于宇航器材,承受高温高速气流的冲刷。
3. It has good thermal performance and is widely used in aerospace equipment to withstand the erosion of high temperature and high speed air flow.
4,工艺性良好,可根据需要设计出各种造型的产品。
4. It has good technology and can design products of various shapes as required.
玻璃钢材料的缺点:
Disadvantages of FRP materials:
1,长期耐高温性差,不过也是普通的玻璃钢的缺点。
1. The long-term high temperature resistance is poor, but it is also the disadvantage of ordinary FRP.
2,老化现象严重,老化是塑料材质的共同缺陷,在风吹日晒下易腐朽
2. The aging phenomenon is serious. Aging is the common defect of plastic materials, which is easy to rot under the wind and sun
玻璃钢材质广泛用于我们行业,假山假树都是有涉及的,下面简单介绍一下玻璃钢假树工艺。
FRP material is widely used in our industry, and the rockery and false tree are all involved. Here is a brief introduction of FRP false tree technology.
1,骨架支撑(一般在翻模拼装的时候焊接)
1. Framework support (generally welded during turnover and assembly)
不管是玻璃钢材料还是水泥材质,前期必不可少的还是支撑的骨架,一般采用角铁焊接主骨架,或直接三角定型座于地面,或用膨胀钉连接于地面或者墙体,另外还要用到6.5的线材作为衔接。
Whether it's made of FRP or cement, the skeleton necessary or supported in the early stage is generally welded with angle iron, or directly triangle shaped on the ground, or connected to the ground or wall with expansion nails, in addition, 6.5 wires are used as the connection.
济南假山制作
2,玻璃钢翻模
2. FRP turnover mold
先找好的树形,把树体一分为二翻硅胶软膜(这里的一分为二不是劈开树体,正反面而已),先用硅胶刷半面树体,然后在软膜外面刷上石膏或者玻璃钢用于固定软膜的形态,把定型的软膜取下,清洗干净,在与树接触的那一面刷上树脂并贴上玻璃纤维,等待凝固,即完成翻模。将双面翻模的成品玻璃钢假树拼接到一起,拼接成品的中间必须有骨架支撑,同时拼接完后,表面要打磨接缝和修补缺失部位。
First find a good tree shape, split the tree into two and turn over the silica gel soft film (here, the split tree is not split, just the front and the back). First brush the half tree with silica gel, and then brush gypsum or fiberglass on the outside of the soft film to fix the shape of the soft film, take off the set soft film, clean it, brush resin on the side contacting with the tree and stick glass fiber, waiting for solidification , i.e. complete the mold turning. Finally, the finished fiberglass false trees with double-sided turnover die are spliced together, and the middle of the spliced products must be supported by skeleton. At the same time, after splicing, the surface shall be polished and the missing parts shall be repaired.
3,上色
3, coloring
我们上色一般都是由大师傅或者美工师傅来完成,材料有多种选择,比如,色浆,丙烯,色粉等等,我们一般采用铁粉研磨而成的材料,是现在市面上相对比较好的材料,色彩多为茶色,或者偏点绿色,当然也有甲方特殊要求的色系出现,调好色系后,可以喷枪喷,可以手工刷,看量的大小。
Our coloring is usually done by a master or a craftsman. There are many kinds of materials, such as color paste, propylene, toner, etc. we usually use iron powder to grind the materials. They are relatively good materials on the market now. Most of the colors are brown or green. Of course, there are some special color systems required by Party A. after the color system is adjusted, spray gun can be used , you can brush it by hand to see the size.
4,上树叶
4. Leaves
树叶一般采用比较好的过胶的树叶,室外不易坏,树叶多少为双方商定量,不是越多越好,稀疏有致才更自然。
Generally, the leaves are better than the glued ones, which are not easy to be damaged outdoors. The number of leaves is determined by the quotient of both sides. The more the better, the rarefaction is the most natural.
版权所有:济南老王假山水景园林

咨询热线:
13064079165
在线客服